Residence in Kallitechnoupolis by Tense Architecture Network

Athens studio Tense Architecture Network has completed a concrete house that staggers down a hillside in rural Greece (+ slideshow).

Residence in Kallitechnoupolis by Tense Architecture Network

Residence in Kallitechnoupolis is a three-storey building that begins near the top of the slope. As it descends, the building widens to create tiered balconies facing out across the landscape.

Residence in Kallitechnoupolis by Tense Architecture Network

Tense Architecture Network describes the structure as a protective shell that shields the house from its neighbours and concentrates views in only one direction.

Residence in Kallitechnoupolis by Tense Architecture Network

“The inclined prism of the shell follows the natural inclination and descends towards the ground via the intensely oblique cut of its eastern front,” says the studio.

Residence in Kallitechnoupolis by Tense Architecture Network

The base of the building cantilevers outwards, making room for a swimming pool on the lowest level, plus an outdoor staircase climbs down one of the side walls to meet a terrace positioned halfway down.

Residence in Kallitechnoupolis by Tense Architecture Network

The architects used concrete for the entire structure, adding a dark tint to the exterior walls so that they contrast with the pale grey interior surfaces.

Residence in Kallitechnoupolis by Tense Architecture Network

“Earthly dark at the outside, lighter in the inside, its colouring is aiming at the maximum possible tension of the shell’s introvertedness,” say the architects.

Residence in Kallitechnoupolis by Tense Architecture Network

Living and dining rooms can be found on the two upper floors, while bedrooms are located on the bottom floor around a series of curved partitions.

Residence in Kallitechnoupolis by Tense Architecture Network

Tense Architecture Network have completed several residential projects recently, including an angular house with a partially submerged body and a house with a boxy concrete upper floor.

Residence in Kallitechnoupolis by Tense Architecture Network

See more architecture by Tense Architecture Network »
See more architecture in Greece »

Residence in Kallitechnoupolis by Tense Architecture Network
Upper floor plan – click for larger image

Photography is by Filippo Poli.

Here’s a project description from Tense Architecture Network:


Residence in Kallitechnoupolis

The residence’s view is a slope: a naked attic slope. The site is significantly inclined and is accessed only through its narrow upper side. The declivity of the site faces an equally slanted hill –the predominant point of visual reference. As the residence neighbours with two extrovert residences on both sides, it realises enclosure, concentration of the view and an introvert escalating development of its open spaces towards the east. The opposing landscape of the hill is perceived from a distance.

Residence in Kallitechnoupolis by Tense Architecture Network
Middle floor plan – click for larger image

The inclined prism of the shell follows the natural inclination and descends towards the ground via the intensely oblique cut of its eastern front. The cut opens the residence to the opposed microcosmos: the air, the light, the barberries, the horizontal ridge, the long lonely railing of the opposite side. A swimming pool is comprised in the shell’s lowest point, partly in cantilever. At the level of the access an elongated excision of the prism allows for a walled yet unroofed outdoor space that eventually concludes to the open eastern front and the view.

Residence in Kallitechnoupolis by Tense Architecture Network
Lower floor plan – click for larger image

The exterior cortex is constructed by exposed reinforced concrete: the shell is two-coloured. Earthly dark at the outside, lighter in the inside, its colouring is aiming at the maximum possible tension of the shell’s introvertness. The geometric austerity of the prism is violently ruptured in three areas: the shell is ultimately found broken, the rupture of its boundaries is performed from within, the remote nature is allowed in. Yet, only as Actio in Distans: only as view.

Residence in Kallitechnoupolis by Tense Architecture Network
Side elevation – click for larger image

Project Team: Tilemachos Andrianopoulos, Kostas Mavros, Nestoras Kanellos
Structural design: Athanasios Kontizas

The post Residence in Kallitechnoupolis
by Tense Architecture Network
appeared first on Dezeen.

Residence in Kato Kifissia by Tense Architecture Network

This family house in Athens by Greek office Tense Architecture Network comprises a boxy concrete upper floor perched atop a glazed living room and kitchen (+ photographs by Filippo Poli).

Residence in Kato Kifissia by Tense Architecture Network

Tense Architecture Network designed the residence with an industrial aesthetic, featuring exposed concrete walls, basalt-cobble flooring and a folded steel staircase suspended by wire cables.

Residence in Kato Kifissia by Tense Architecture Network

The ground and first floors are offset from one another and dark-tinted concrete columns support the overhanging bedroom floor.

Residence in Kato Kifissia by Tense Architecture Network

“The main volume is vigorously elevated – nearly four metres high – in order to liberate the ground floor,” architect Tilemachos Andrianopoulos told Dezeen. “The top floor’s austerity towards the public facade realises an intentional contrast to the receptivity of the ground-floor spaces, which open up completely to the garden through the sliding glass panels.”

Residence in Kato Kifissia by Tense Architecture Network

A system of wires is strung up around the house, intended to encourage climbing plants around the building. “The industrial material character of the house is advantageously complemented by the greenery,” explained Andrianopoulos.

Residence in Kato Kifissia by Tense Architecture Network

A pivoting door provides the entrance and leads through to the living room and kitchen, which are divided on split levels. The steel staircase ascends towards three bedrooms on the top floor, while a concrete staircase descends to the basement.

Residence in Kato Kifissia by Tense Architecture Network

Athens studio Tense Architecture Network also recently completed another concrete house in the Greek countryside. See more architecture in Greece.

Residence in Kato Kifissia by Tense Architecture Network

See more photography by Filippo Poli on Dezeen or on the photographer’s website.

Residence in Kato Kifissia by Tense Architecture Network

Here are a few words from Tense Architecture Network:


Residence in Kato Kifissia, Athens

The residence’s plot is small and an adjacent building almost blocks the southern sun. The complete “colonization” of the suburb has almost eliminated the previously exuberant vegetation in the rush to meet individualistic private housing.

Residence in Kato Kifissia by Tense Architecture Network

As a first act, the desire to reside defines an area and makes a house, in it: a cubic shell of plants creates a limit for the residence, as area. In order to reside, one withdraws inward.

Residence in Kato Kifissia by Tense Architecture Network
Ground floor plan

The residential space claims the whole field, as well as the sun; two parallelepiped volumes, one small and attached to the north, the other cantilevered and central, free the ground and enable the sun to enter.

Residence in Kato Kifissia by Tense Architecture Network
First floor plan

When the plants are fully grown the green facade will be penetrated only by the black, central column of the shelter by exposed concrete. The basalt-watery surface on which it is anchored reflects the light in the interior.

Residence in Kato Kifissia by Tense Architecture Network
Front elevation

Project Team: Tilemachos Andrianopoulos, Kostas Mavros, Nestoras Kanellos

The post Residence in Kato Kifissia
by Tense Architecture Network
appeared first on Dezeen.

D38 Zona Franca Office by Arata Isozaki

Modular offices open out to terraces on each floor of this building in Barcelona by Japanese architect Arata Isozaki (+ slideshow with photographs by Filippo Poli).

D38 Zona Franca Office by Arata Isozaki

Completed in April, the project is the first in a three-phased office development masterplanned by Isozaki alongside former Foreign Office Architects partners Alejandro Zaera-Polo and Farshid Moussavi for a site in the industrial district of Zona Franca.

D38 Zona Franca Office by Arata Isozaki

The glass-panelled facade is covered with a pattern of white and green dots, which reduce glare into the offices behind.

D38 Zona Franca Office by Arata Isozaki

The building has a square-shaped plan where each level surrounds a central core containing staircases and lifts.

D38 Zona Franca Office by Arata Isozaki

Offices floors have either a C or L-shaped layout and can be subdivided into two or three units.

D38 Zona Franca Office by Arata Isozaki

Last year Isozaki unveiled designs for an inflatable concert hall by himself and artist Anish Kapoor.

D38 Zona Franca Office by Arata Isozaki

See more offices on Dezeen »

D38 Zona Franca Office by Arata Isozaki

See more projects in Spain »

D38 Zona Franca Office by Arata Isozaki

Here’s some text from Arata Isozaki & Associates:


D38. Zona Franca, Barcelona

DISTRITO 38 is an office-­park project of 70,000 square meters developed on a 35,000 square meter lot, which is to be built in three phases according to a master plan produced in collaboration with FOA.

D38 Zona Franca Office by Arata Isozaki

The area can be found at the foot of Montjuic hill, to the west of Barcelona, in a zone abounding in office projects currently under development, thus converting the area into an important tertiary centre located close to the airport and the seaport.

D38 Zona Franca Office by Arata Isozaki

There exists great diversity in office spaces at present, and since the final use and necessities of these offices are still unknown, an open system that allows for posterior reorganisation according to new and developing requirements was chosen.

D38 Zona Franca Office by Arata Isozaki

The lot faces a representative part of the Paseo de Zona Franca.

D38 Zona Franca Office by Arata Isozaki

Using this as a reference point, a 7.5 x 7.5 meter grid defined by a structural mesh has been deployed, from which point the parking area as well as the six planned buildings will be developed.

D38 Zona Franca Office by Arata Isozaki

Building 1 has been conceived as a parallelepiped, measuring 52.5 x 52.5 meters on the sides with a height of 46.5 meters, and featuring a central core from which parts will be subtracted perimetrically from the volume.

D38 Zona Franca Office by Arata Isozaki

This ‘subtraction game’ leads to better location adaptation, a hierarchy in the different façades, and easier adaptability in the creation of office settings, ideal in this highly fluctuating market.

D38 Zona Franca Office by Arata Isozaki

The office floors are available in two distinctive types: the L and the C shape, and the interior of each may be organised into and sold as one,two or three units.D38 Zona Franca Office by Arata Isozaki

The post D38 Zona Franca Office
by Arata Isozaki
appeared first on Dezeen.

Casa Pocafarina by Hidalgo Hartmann

Casa Pocafarina by Hidalgo Hartmann

The four concrete wings of this house in Girona, Spain, appear to hover in the air above an underground entrance (photographs by Filippo Poli).

Casa Pocafarina by Hidalgo Hartmann

Completed in 2010 by Barcelona studio Hidalgo Hartmann, the single-storey Casa Pocafarina has a cross-shaped plan that sits on four pillars and hovers a metre above the lawn.

Casa Pocafarina by Hidalgo Hartmann

The underground driveway tunnels down beneath the floor of an en suite master bedroom to arrive at a staircase that ascends into the heart of the house.

Casa Pocafarina by Hidalgo Hartmann

Two children’s bedrooms and bathrooms are situated in the wing opposite, while a living room and a dining room occupy the remaining two sides of the cross.

Casa Pocafarina by Hidalgo Hartmann

A square courtyard surrounded by glass is concealed at the centre of a building.

Casa Pocafarina by Hidalgo Hartmann

Photographer Filippo Poli also shot a concrete centre for rescued turtles, dolphins and birds by the same architects – see it here.

Here’s some more text from Hidalgo Hartmann Arquitectos:


Memory

The house is situated on a corner plot with some good views over the distant landscape.

Casa Pocafarina by Hidalgo Hartmann

In order to enjoy these views and avoid the neighboring buildings, the ideal configuration for the house was to create a compact form of cross which is placed at the center of gravity of the plot.

Casa Pocafarina by Hidalgo Hartmann

The four wings are oriented in a way that ensures the selected views from inside the house.

Casa Pocafarina by Hidalgo Hartmann

The whole volume is supported by four pillars and cantilevers out over the garden level at a hight of one meter.

Casa Pocafarina by Hidalgo Hartmann

The pillars itself are based on the lower ground floor of 8x8m that contains access to housing, the porch, garage and laundry.

Casa Pocafarina by Hidalgo Hartmann

On the top floor, the cross-shaped plan organizes the four wings around a central space, an exterior courtyard, that provides sunlight into the heart of the house.

Casa Pocafarina by Hidalgo Hartmann

The four wings contain the different functions of the house with the living room area and the kitchen-dining area connected with each other through the transparency of the courtyard.

Casa Pocafarina by Hidalgo Hartmann

Distributed on both sides of this main space there is the master bedroom with it’s own bathroom and the two children’s bedrooms also with a bathroom hidden by a concrete wall.

Casa Pocafarina by Hidalgo Hartmann

The use of concrete in its natural colour and made with wood slats all over the house reveals visibly the powerful construction that is needed to realise the idea in a coherent way.

Casa Pocafarina by Hidalgo Hartmann

Authors of the project: HIDALGO.HARTMANN, Jordi Hidalgo Tané, architect, Daniela Hartmann, interior designer.
Technical Architect: Rafel Serra Torrent, Technical Architect.

Casa Pocafarina by Hidalgo Hartmann

Collaborators: Torrent Rafel Serra, Technical Architect, Ana Roque, architect.
Promoters: Xevi Bartrina i Alba Sarola.

Casa Pocafarina by Hidalgo Hartmann

Construction: Estructures Olot S.L (concrete) LI-BRA S.L (general constructor) Fusteria Serra (Word furniture) Plantalech (Aluminium charpenter) Cuines Santi, Olot (Kitchen) Electrica Masaló (fluids instalation) Electricitat Quim (electrical instalation)

Christ’s Resurrection Church by Cino Zucchi Architetti

Christ’s Resurrection Church by Cino Zucchi Architetti

Photographer Filippo Poli has sent us these images of a Milan church with a grey, striped exterior by Italian studio Cino Zucchi Architetti.

Christ’s Resurrection Church by Cino Zucchi Architetti

The striped facade is composed of vertical panels of concrete, white stone, zinc and glass.

Christ’s Resurrection Church by Cino Zucchi Architetti

Containing both a church hall and a parish centre, Christ’s Resurrection Church replaces a warehouse church that previously occupied the industrial site.

Christ’s Resurrection Church by Cino Zucchi Architetti

The otherwise rectangular building has an angled wall and roof that create a point at one corner, framing the main entrance.

Christ’s Resurrection Church by Cino Zucchi Architetti

Inside the church hall two concrete walls curve up to the ceiling, creating the illusion of a pitched roof.

Christ’s Resurrection Church by Cino Zucchi Architetti

More stories about churches on Dezeen »

Christ’s Resurrection Church by Cino Zucchi Architetti

More projects in Italy on Dezeen »

Christ’s Resurrection Church by Cino Zucchi Architetti

The following information was provided by the architects:


“Christ’s resurrection” Church, Sesto S. Giovanni (Milan) 2004-2010

Cino Zucchi Architetti with Zucchi & Partners

Closed competition –first prize

The new church and parish center is located in a narrow plot of Milan’s industrial periphery.

Christ’s Resurrection Church by Cino Zucchi Architetti

The hard townscape of the neighbourhood and the story of the previous church (a warehouse-like building built in the sixties by workerpriests) suggested the simplicity of its design, which emerges from the surrounding fabric only by few strong gestures.

Christ’s Resurrection Church by Cino Zucchi Architetti

The street façade bends inward to acquaint for the main diagonal view, and the high hall takes the shape of a large rectangular box enriched by two large “sails” embracing the assembly.

Christ’s Resurrection Church by Cino Zucchi Architetti

The fronts are panelled in vertical strips of different materials (concrete, white stone, zinc, glass) whose rhythm responds to the different edge conditions.

Christ’s Resurrection Church by Cino Zucchi Architetti

Credits:

Client: Diocesi di Milano
Dimensions: 6.570 m³

Christ’s Resurrection Church by Cino Zucchi Architetti

Preliminary design project: Cino Zucchi Architetti
Cino Zucchi, Helena Sterpin, Filippo Carcano, Cinzia Catena, Silvia Cremaschi, Cristina Balet Sala
with Anna Bacchetta, Annalisa Romani, Martina Valcamonica, Valentina Zanoni

Christ’s Resurrection Church by Cino Zucchi Architetti

Definitive and executive design project: Zucchi & Partners
Cino Zucchi, Nicola Bianchi, Andrea Viganò, Leonardo Berretti, Ivan Bernardini

Christ’s Resurrection Church by Cino Zucchi Architetti

Click above for larger image

Manager of works: Zucchi & Partners
Nicola Bianchi, Marcello Felicori

Christ’s Resurrection Church by Cino Zucchi Architetti

Click above for larger image

Rendering: Filippo Facchinetto
Model: Filippo Carcano, Paola Andreoli, Roberto Rezzoli

Christ’s Resurrection Church by Cino Zucchi Architetti

Click above for larger image

Consultants
Liturgist: Don Giovanni Mariani, Don Giovanni Zuffada
Cost estimate: Zucchi & Partners
Structural engineering: Mauro Giuliani, Redesco srl
Ligh engineering: Cinzia Ferrara, Ferrara Palladino srl
Plant engineering: Gianfranco Ariatta, Ariatta ingegneria dei sistemi srl

Christ’s Resurrection Church by Cino Zucchi Architett

Click above for larger image


See also:

.

Church in by Massimiliano
and Doriana Fuksas Architects
Tampa Covenant Church
by Alfonso Architect
Notre Dame Rosary Church
by ENIA Architects

Auditorium Atlantida by Josep Llinas

Photographer Filippo Poli has sent us some images of an auditorium in Vic, Spain, made from a jumble of golden blocks by architect Josep Llinas. (more…)