Hasta La Ideas

The roof and upper walls of a house in Tübingen, Germany, are covered in rubber, like a fisherman’s hat pulled low over his eyes.

Designed by German studio Architekten Martenson und Nagel Theissen, the five-storey Just K house has walls that pitch in and out to maintain views from neighbouring houses to a nearby castle.

The raised seams that line the house are welded together and allow rainwater to naturally drain from the walls.

As the family grows, the house could be split into two separate residences with entrances on the basement floor and at first floor level, accessed by an outdoor staircase.

Rooms are warmed and cooled by passive house technology, where hot air is drawn up through the building by a ground-air heat exchanger, and solar panels on the south elevation provide additional electricity.

An open plan living room with a raised living area platform occupies the ground floor, while two floors of bedrooms and an attic living room are located above.

Exposed softwood provides the surfaces of walls, floors and ceilings throughout the timber-framed house.

A recent debate on Dezeen questions whether the use of exposed timber inside houses (particularly in Japan) is a consumptive trend that should not be encouraged just because of its natural appearance – join the debate here.

This is the second project by Architekten Martenson und Nagel Theissen on Dezeen this month, following a cafe pavilion in a town cemetery edged with both round and pointed arches.

Photography is by Brigida González.

Here are some more details from the architects:

Project: Just K

Living space for 2 adults and 4 children in Tübingen

Site and commission

This 365 square-metre site is located in Tübingen; on a south-facing slope with a view over the city and of Tübingen castle. The 1960s development plan stipulates a specific position for the house on the site as well as “insertion into the surroundings” according to §34 of the Federal Building Code. The client commissioned the design of a family home that would provide passively heated living space for two adults and four children. Use of energy efficient passive house technology, natural application of materials and prudent use of the resources at hand, make the building sustainable. The potential adaptation of the house to the family’s living situation was an important aspect thereof.

The question is, what is “good” living space? What defines it and what does one really need? These issues guided us in our approach to the layout of the house, which has been efficiently designed to optimally deliver maximum use of space, functionality and flexibility. We strove to create outstanding spatial quality using a minimum of materials. Imaginative overlapping of spatial areas and uses were designed to give the inhabitants a feeling of spaciousness, manifold atmospheres and various realms of possibility—despite minimised living area.

Envelope

The parameters of a limited-sized site, distance spacing regulations, and ample living space for six people, led the building to grow upwards in tower-like fashion. JustK relates to the surrounding grey 1920s tuff buildings in a contemporary manner through its compact envelope and defined roof volume. The swing of its hipped roof and its multiply-kinked shape derive on the one hand from a desire to create maximum spatial volume with minimum distance spacing, which the 70° angle facilitates in adherence to state building regulations, and on the other hand from a request by the neighbours to keep the view of Tübingen Castle unimpeded—under which conditions they sold the site.

Roof Cladding

The top and roof level of the house has been clad in a “southwester hat” of roof sheeting to provide protection from wind and weather. Similar to exterior “seams”, the roof sheeting meets to form ridges at the edges, these have been welded together to stand out from the water surface. This interpretation of the ridge seal accentuates the envelope of this membrane-covered warm roof. A drainage edge on the eaves guides away the rainwater that falls on the roof cladding, just like the brim of a hat.

Prefabrication, Structure, Surface Treatment

The structural physical demands on passive houses, their short construction period as well as sustainability considerations, all culminated in a decision to build this house in solid wood, optimally using the potentials of prefabrication. The whole building consists of 136 elements, which were fabricated with notches for carpentry and joinery as well as with drill holes and grooves for installation of the electrics.

Wood is the main material to be used consistently throughout the structure and interior surfaces; as a renewable raw material it was chosen not least for its favourable energy balance. To keep costs down, the wooden surfaces in the common rooms have been designed in “refined shell construction.” The industrial surface of these cross-layered wooden elements have been sanded down, bucked and soaped to preserve the light character of the wood.

Splittable

One can become two. Sustainable and flexible; the house can be split into two living units with separate entrances without much effort should the family situation change to require that. The total area of the house is 138 square-metres; one unit would measure 81 square metres and the other 57. In the warmer months of the year, this living space can be extended by the 12 square-metre balcony and the 23 square-metre forecourt.

Ground floor Climate Zone

The staggered main living space creates various room heights which zone the ground floor and automatically create different climate zones in winter. Cold outside air remains trapped in the lower entrance area while moderate temperatures prevail in the kitchen-living room and the sitting room higher up is warmest.

Architects: Björn Martenson, Sonja Nagel and Jan Theissen.
Structural planning: Ingenieurbüro von Fragstein
Energy planning: Dipl.-Ing. Jörg Lammers

Site: 365 m²
Floor space: 138 m² (81m² + 57 m²)
Gross floor area: 278 m²
Cubic content: 583 m³
Energy needs: 14,4 kWh/(m²a)
Building costs: € 330.000,-
Design period: November 2007 to December 2008
Construction period: April 2009 to June 2010 (with discontinuities)

Firms involved:
Cross-Laminated Structural Timber Pabeks/Lenotec: Finnforest Merk GmbH
Synthetic Membrane Roof: Roofing Membrane, synthetic rubber/ Polyisobutylene (PIB)
Composite Thermal Insulation System: Sto AG
Ventilation system: Drexel und Weiss Energieeffiziente Haustechniksysteme Gmbh
Windows – Alu2Holz: Optiwin GmbH
Skylight Windows: Fakro Dachfenster GmbH
Sloped Glass Roofs: RAICO Bautechnik GmbH

See also:

.

Wrap House by Future Studio	Villa Bussum by GROUP A	Yachiyo by Atelier Tekuto